| 1. | Strain gauge installed by spraying process
喷涂式应变计 |
| 2. | Safety code for painting - safety for electrostatic powder spraying process
涂装作业安全规程粉末静电喷涂工艺安全 |
| 3. | Three - dimensional numerical simulation of the spray process in swirl chamber with a hybrid breakup model
利用混合破碎模型对涡流室内喷雾过程的三维数值模拟 |
| 4. | The light housing is made of high quality steel material which is treated with advanced static electricity spray process
格栅灯盘是由高质量的冷轧钢板制成，表面经过先进静电喷涂处理。 |
| 5. | The paper introduces the technological processes of electrostatic powder spraying on large - sized workpiece and some issues that should be paid attention during spraying process
摘要介绍了大型工件静电喷粉的工艺流程，以及在实施过程中，应注意的若干问题。 |
| 6. | The system can monitor four major indexes in the spraying process , the spraying pressure , spraying flow , sprayer travel speed rate and the percentage of the remaining mix pesticide in the tank
该系统可实时监测喷施农药过程中的喷雾压力、喷雾流量、喷雾机行走速度和药桶药液余量4个主要参数。 |
| 7. | The spray processes of throttling and normal pintle nozzles are investigated in this paper . the test results show that the better spray characteristics and spray quality can be achieved when the throttling pintle nozzle is used in small diesel engines
本文对节流轴针式和普通轴针式喷油嘴的喷油过程进行实验研究，试验结果表明，节流轴针式喷油嘴应用在小缸径柴油机上能取得良好的喷油特性和喷雾质量。 |
| 8. | The nature conservancy of cement tile blank . after the surface coating production line in preheated purge bottom spray drying intermediate layer spray drying launched drying table a total of three cooling heating and drying surface , the second spraying process , weatherability cement tiles surface coating to achieve the best performance
自然养护后的水泥瓦坯，在涂装生产线上经过表面吹扫预热干燥底层喷涂中间干燥面层喷涂面涂干燥表面冷却共三次加热干燥二次喷涂的工艺过程，使水泥彩瓦表面耐候性涂层达到最佳性能。 |
| 9. | Quenching systems for induction hardening may utilize various agitation modes including : conventional immersion quenching , open spray and submerged spray processes . these are not equivalent processes and proper engineering dictates that they be appropriately addressed . an overview of these different agitation systems is provided
感应淬火冷却系统可能采用各式各样的搅拌方式,包括传统的浸淬、开放式喷雾冷却和浸没状态下的喷射冷却.这些工艺并不等效,而是要根据正确的技术要求来恰当地选用这些方法.本文对这些不同的搅拌系统进行了综述 |
| 10. | This paper reviewed the modeling and experiments of the transient phenomena involved in the various subsystems of the thermal spraying process at home and abroad , such as : effect of process on droplets behaviors , microstructure , residual stress analysis and spray materials , and based on experimental resuts to discuss the droplets thermal - transfer discipline and effects on coatings properties
摘要从热喷涂工艺参数对涂层形成的影响、微观组织及残余应力分析和喷涂材料等几方面对国内外热喷涂涂层形成机理的研究进展进行综述，重点综述了工艺参数影响液滴行为的研究，并结合试验探讨了液滴的热传输规律及对涂层最终性能的影响。 |
